conteHome > Ice Maker > Kenmore Coldspot Ice Maker Not Working

Kenmore Coldspot Ice Maker Not Working

Contents

Sign in to report inappropriate content. Making the unit think the door was closed. 2. Back to top #4 Ravenar Ravenar 1,000 Post Club! 2,612 posts Joined: Jun-02 2000 LocationStaten Island Posted July 07 2012 - 7:55 PM Well I took the whole ice maker out. Share your feedback in the Ideas section. this content

Finally had a chance to change the valve. This is located toward the bottom of the refrigerator. To see if it is the valve not sending water you can put 4 and 3/4 oz of water (135cc) into the icemaker and in an hour 1/2 or less it PartSelect 90,613 views 9:00 Loading more suggestions... http://www.applianceblog.com/mainforums/threads/8007-Kenmore-Coldspot-Ice-Maker-Stopped-Working

Kenmore Coldspot Ice Maker Not Making Ice

Thank again. by Manage My Life December 6th, 2010 Comment 0 votes No doubt you will need to replace the emitter and receiver board. First the pins for the electric were backwards.

I filled the mold last night and it didn't harvest. SamuraiRepairman 263,494 views 2:34 Loading more suggestions... You will need to pull out the icemaker and jumper the thermostat. Kenmore Coldspot Ice Maker Leaking Water I have been completely mistreated by Sears Outlet and I NEED to speak to someone about this.

Expert: Appliance Tech Dave replied7 years ago. Kenmore Coldspot 106 Ice Maker Red Light Blinking Hope this information helps someone else. These are the optics boards for your model refrigerator: Receiver Circuit Board - part # PD00004896 (mfg # W10518658) Emitter Circuit Board - part # PD00004894 (mfg # W10518659) Ryan www.PartsDr.com

Don't see what you need?

What's New? Kenmore Coldspot 106 Ice Maker Diagram Accerlice 2 light is on. The ice dispenser motor is working fine. I will pour in water now.

Kenmore Coldspot 106 Ice Maker Red Light Blinking

If the icemaker still will not operate with a 15F or lower thermostat there is a problem in the icemaker. Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. Kenmore Coldspot Ice Maker Not Making Ice It appears it was the valve. Kenmore Coldspot 106 Ice Maker Manual Our troubles started January 2016 with our Kenmore 795...

After this time frame, I expect more than an apology. http://sparcweb.net/ice-maker/kenmore-refrigerator-ice-maker-not-working.php Submitted: 7 years ago. Nothing happening. Expert: Appliance Tech Dave replied7 years ago. Kenmore Coldspot Ice Maker Not Getting Water

All times are GMT -5. DELAY(REPEATED) POSSIBLE CAUSES: The flapper door on the emitter is blocking the beam or the optics are faultly. Tips & Warnings Be very cautious when working with electrical appliances in wet areas. have a peek at these guys Track assembly installation.Do-it-yourself troubleshooting and repair videos only at ApplianceVideo.comWe take you into a real customers home with Ace Appliance in Toledo, OH to teach you how to "Fix it Yourself

If you use eBay you can get one for half that price. Kenmore Refrigerator Ice Maker Not Making Ice Once the ice bucket is full, the metal arm raises and shuts off the ice maker. I don't even think this board has a light?

Remove this piece and disconnect the harness from the control.

Has power and isn't defective.) 5. Ask Your Own Appliance Question Customer: replied7 years ago. Make sure the unit is unplugged before placing your hands near the power source. Kenmore Coldspot 106 Ice Maker Removal Fix your trusty Whirlpool Refrigerator that has some of the following problems: Ice build up in the bottom freezer By visiting us at http://www.appliancevideo.com To complete this repair use a W10309238

Door removal. It should come with instructions. AppliancePartsPros 629,039 views 9:55 Sears, Kenmore, Whirlpool & Maytag Refrigerator Repair & diagnostic - Leaking water on floor - Duration: 13:52. check my blog This is really ridiculous.

Sign in Transcript Statistics 57,851 views 20 Like this video? You may have to register before you can post: click the register link above to proceed. Second all the tubes have compression fittings(the old one had screw on fittings). The only other solution would be a complete new ice maker.

This is my second set of front load washer and dryers from Kenmore/ Sears - and will be my last. OK> Wait how long? First tell me what position is the ejector arm fingers are pointing? Please help! see more...November 10, 2016 · Answer · Like0 · Follow0 Show 6 answers allyson.rainieriWhy doesn't the Kenmore 790 wall oven have a recall on it?

nt