conteHome > Iphone 3g > Iphone 3g Not Working After Replacing Screen

Iphone 3g Not Working After Replacing Screen

And the instruction to "..insert a metal spudger between the two metal rails along the edge of the display assembly.." didn't really help. Loading... Then I spent the next 5 minutes slowly carefully wiggling the cable back into place without lifting the tab. Let us know how you get on. Check This Out

So I took it apart again, and again, and again. PileOfMush - 08/26/2009 Reply Failed :( I didn't found the way to lift and broke in 2 the connector for #3. it usually in a way "tricks" your motherboard into thinking your LCD is on when it is not, and and when it is all together your LCD is black. the only thing working was the digitizer.

Also, when removing that foam sticker make sure you peel from underneath the sticker not in the middle of the foam. Hope this helps. Yes No Voted Undo Score 0 Cancel Comments: iPhone 3GS Display Assembly Replacement follow this to check on your connections. Never apply too much force or twist LCD as you slide it out as its VERY fragile and expensive to replace.

Funny thing was that they were so close to each other that you couldn't tell the difference between them. We used the hair dryer and heated the glass side and pryed as I went and it all came up. Discharged battery, recharged, hard reset 4. I also recommend that people observe some basic ESD precautions.

Tab is open and I tried to get in the ribbon cable. no glue. Hi I dropped my Iphone on rocks, the LCD panel brok and i replaced it with the front panel kit (the front panel and LCD screen kit). https://www.ifixit.com/Answers/View/47721/Screen+not+responding+after+replacement. The mid-frame section is now readily available as an orderable spare part and in my opinion you’ll get a much neater, cleaner repair if you replace this part too.

Be careful with the heat gun, go slowly and only heat small portions at a time but it works much better than a hairdryer. Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears restore the iPhone software. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Fixing the digitizer - If I want to open the iPhone, What are the risks on the way to the digitizer?

I suggest you reinstall it, or even better, have someone with the knowledge, experience and equipment to do it properly do it for you. https://www.ifixit.com/Answers/View/20475/iPhone+3G+Glass-Digiter+Replacement%3A+Screen+Now+Black This will keep glass shards contained and provide structural integrity when prying and lifting the display. I sorced a new one locally for £25 and it now works fine. filzstiftman - 08/29/2011 Reply Add a comment Add Comment 1024 Step 12 Edit Turn the display assembly over and again carefully insert a metal spudger between the two metal rails along

Jan 10, 2010 9:50 PM Helpful (0) Reply options Link to this post by modular747, modular747 Jan 11, 2010 5:59 AM in response to Brian965 Level 6 (19,343 points) iPad Jan his comment is here digitizer 1485 Questions View all Shai Rep: 227 6 17 Posted: 05/21/2011 Options Permalink History Subscribe Unsubscribe How to fix iPhone 3G Digitizer? (Touch is not responding) Hi, I have iPhone Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit. I had to use a pair of tweezers to slide it in all the way.

The screen was popped out at the top edge, and I really didn't want to drive to the Apple Store. Loading... United States Copyright © Apple Inc. this contact form Up next iPhone 3G / 3GS Touch Screen Glass Digitizer Repair Tutorial - Electrolowcost.com - Duration: 9:11.

Cancel MARC Rep: 13 1 Posted: 11/19/2011 Options Permalink History had same as above problem (black screen on reassembly) after replacing the complete 3 part lcd screen, digitizer / button assembly, Get in between the sticker and metal of the top of the connector. pbrookei - 10/07/2009 Reply The guide work well with tear down but I have a small problem with the screen fixing with a slight gap ?

perhaps your screen sits a bit akimbo because you still have some goo in those rails?

FYI. screen not working 1485 Questions View all jpwfranks Rep: 11 Posted: 03/22/2011 Options Permalink History Subscribe Unsubscribe Screen not responding after replacement. Man, I'm so happy now. the clue to what may have broken will be in the area of most damage to the phone.

deanmcrobie - 10/08/2009 Reply so the kit I got sent me all the tools I need including the glass panel but step 12 said to separate the lcd from the glass Was my first iPhone screen replacement :) Damien - 04/30/2010 Reply Replaced the the touch screen and now the phone earpiece no longer work. The fact that the phone "isn't working at all" and can't be turned off suggest there is a lot more wrong. navigate here Is my connection faulty?

does it make sounds? 11/18/2010 by Gabe no, there is no sound or reaction wen i plug it and the screen don't light up tommy 11/19/2010 by Tommy Was the phone There is a white line with an arrow. I did run into three problems: 1) I broke one of the connectors that supply power/information to the home button :(. 2) The display works but the buttons do not match I think 1 and 2 snap, 3 is a ribbon cable that requires you to loosen the small clip to remove it.

So I took hers apart and tried to replace her 3GS iPhone with my old 3G touchscreen. The FPC locking latch is very delicate and is typically a different color than the body of the connector. (see the detail image of FPC connector open and closed) Slide the Proceed like a neuro-surgeon. This is entirely a new issue...even with a cracked screen like my original was, it still responded to all touches.

Maybe because it was on this al, happened but it would turn on w/o any probs the 1st couple times, just the darn home button, oh and I booted into safe iCracked 200,185 views 17:03 iPhone 3G TouchScreen Repair Part 5 - Duration: 10:12. After the repair my gps is not working like it was before. After getting the cable in the connector, use your third and fourth hands to put a small pre-cut piece of tape on the top of the cable and on to the

Yes No Voted Undo Score 2 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? I powered off the phone before the install, and then powered it on at the last step of attaching the cables, to verify all was connected fine. Please help!!!!! Was this answer helpful?

yosarian - 07/20/2009 Reply Hello everyone -- what kind of adjustments, if any, can be made in this step to ensure that the display sits flush with the bezel around all I managed to get it under the white connector as securely as I could. Reply about broken tab on cable #3. PileOfMush - 08/26/2009 Reply And in this picture of the 3GS, the colors are inverted...

nt