conteHome > Macbook Pro > Macbook Pro Usb 3.0 Not Working

Macbook Pro Usb 3.0 Not Working


Much appreciated thanks! :) Reply Macgrilla Gorilla says: November 5, 2015 at 2:30 pm An increasing number of 10.11 and 10.11.1 users with USB connected devices are stating issues with these Reply Samodelkin says: August 11, 2016 at 6:53 am USB hub issues ("USB Device Needs Power" alert when plugged in into the hub) can be fixed with this kext: Reply The question is, what can I do? If they are black then you have a 2.0 logic board which may have been installed in a newer models case.

How do you put a reference next to image? No big deal either way really since I do have the 2nd USB port on my MacBook Pro free to plug the mouse into until the issue is resolved. This didn't fix it. JLatte, Aug 18, 2015 JLatte macrumors 6502 Joined: Dec 2, 2005 Location: San Diego #25 Grothesk said: ↑ i have this weird bug with usb-c on dp6 on my macbook. weblink

Macbook Pro Usb Not Working

arfung, Aug 16, 2015 arfung macrumors newbie Joined: Jun 27, 2015 #22 I was having some serious problems with USB on DP6 - to the extent that thumb drives wouldn't mount. Jul 26, 2012 9:50 AM Helpful (0) Reply options Link to this post by STUPENDOUS!!!, STUPENDOUS!!! share Share on Twitter Share on Facebook Email Link Like + Quote Reply TonyC28, Aug 17, 2015 TonyC28 macrumors 65816 Joined: Aug 15, 2009 Location: Mokena, IL #24 USB on my

The card reader doesn't show up. Yes this is quite technical and maybe only suited for an electronics engineer, but I am not and I can do it. Keep holding the keys (Option + Command (⌘) + P + R) until your MacBook restarts (You will see the grey screen appears before it restarts.) Step 05. Reset Usb Ports Mac Use a different connector on the device end than USB 2 cables.

If it's already connected, leave as is. Usb Not Recognized Mac Why don't I see blue inserts on theUSB ports of my Mac? What happens if I plug in a USB 2 device into the USB 3 port first?If you plug in a USB 2 hub first, all devices connected or "daisy-chained" to that Power button is not on my keyboard, I pushed my "on" button along with Shift+Control+Option, had to release the power button but held the other 3 until power light switched off

Very frustrating, with seemingly no upside to whatever engineering changes were made. Macbook Pro Usb Ports Not Working Fix Resetting SMC worked for me. Reply Leave a Reply Cancel reply Your email address will not be published. Is there an actual army in 1984?

Usb Not Recognized Mac

My seemingly non-working USB port now recognizes my devices. Step 01. Macbook Pro Usb Not Working any thoughts? Imac Usb Ports Not Working Similar issue, I have an external HDD and card reader which connected via a powered USB 3 hub.

Hopefully the next update will fix it. this page I did a force shutdown and then when it rebooted, it won;t recognize all usb 2.0….it can't even charge my iPhone when plugged to the right side or even a pen Some people with Hackintoshes have done this: but I'm unclear on whether it would benefit us. Enter your email address below: Related articles: Change MAMP to Default Apache and MySQL portsHow to Chat on AIM from Behind a Firewall with iChatSee What Files & Ports an Application Macbook Pro Not Recognizing Usb

share Share on Twitter Share on Facebook Email Link Like + Quote Reply jruschme, Jul 29, 2015 jruschme macrumors 6502 Joined: Dec 20, 2011 Location: Brick, NJ #13 Here's a good When you find the device causing the problem, review its documentation for further troubleshooting steps. Are USB 3 hubs supported? get redirected here Here is how you can perform the NVRAM reset on a Mac to see if this resolves the USB failure: Restart the Mac, and immediately hold down Command + OPTION /

No, create an account now. Usb Devices Disabled Mac Advertise on MacRumors Our Staff Arnold Kim Editorial Director Email • Twitter Eric Slivka Editor in Chief Email • Twitter Juli Clover Editor Email • Twitter Joe Rossignol Editor Email • So, if you ever encounter total USB failure on a Mac for no apparent reason, try the SMC reset, it will probably work for you too.

Reproduction without explicit permission is prohibited.

Now it has stopped working--not even showing any indicator lights when plugged in. In the window that appears, see if the USB device is listed below Hardware in the Contents list. Jul 4, 2012 1:41 PM Helpful (0) Reply options Link to this post by EQAL, EQAL Jul 14, 2012 12:49 AM in response to JoshRoedaMacUser Level 1 (0 points) Jul 14, Mac Not Recognizing Usb Device The SMC should not need to be reset unless you change a fundamental aspect of your hardware (add ram, swap a drive, etc.).

Why don't someUSB 3 devices activate or appear on the USB 3 bus? when i charge it and remove the power chord usb-c stops working until i reboot the machine. Sometimes unplugging and plugging the device back in can resolve the issue. useful reference bla, bla, bla.

Is there an actual army in 1984? But according to your link above, it does look like Apple is aware of problems in many situations at this point. share Share on Twitter Share on Facebook Email Link Like + Quote Reply TiGr67 likes this. Are there differences between USB 3 cables and other USB cables?

share Share on Twitter Share on Facebook Email Link Like + Quote Reply Fuchal, Jul 27, 2015 Fuchal macrumors 68020 Joined: Sep 30, 2003 Location: Boston #6 Had the same problem No combination works. Please type your message and try again.            JoshRoedaMacUser Level 1 (0 points) Q: Retina Macbook Pro - USB 3.0 not working properly? All rights reserved.

Ask Different works best with JavaScript enabled iFixit: Repair Manual Official App Free – Google Play Install Select a Language: 中文 日本語 Deutsch English Español Français Italiano Nederlands Português Русский язык I really think this is not cool. Are you using an USB-hub? Reply JP says: February 5, 2016 at 9:15 am Never heard of jag before.

Learn more aboutidentifying USB ports on your Mac. Press and hold the power button for 5 seconds. At the end of the day, it is the lie is what I find most annoying about this. UPDATE (09-Oct-2016): SOLUTION -- It's LeapMotion's Fault!!

Same with the iPad and charging, if no other devices are connected, it still beeps all the time and doesn't charge properly. In the window that appears, click Overview, then click the System Report button to open System Information. Reply bruno says: November 28, 2015 at 5:33 am It worked like a charm! They are 3.0 ports, which you can check on using System Profiler.

We are going to reset the SMC and the PRAM to fix this issues. Thank you sooooo much!!!! Provide feedback via Please be kind when reporting issue, as these are the people who can help you. My USB port works now.