conteHome > Not Working > Inground Pool Spa Jets Not Working

Inground Pool Spa Jets Not Working

Contents

When the pump is on and all valves are turned properly (I know that they are right as it was previously working) the jets will not blow with much force, and Not sure what to do next to get the pressure back. I believe the piping to and from the spa is 2" pool products ~ swimming pool pumps "Live in the sunshine, swim the sea, drink the wild air." ~ Ralph Waldo Undo just-a-pb How did you check that the spa jets are clear. have a peek at this web-site

Another problem with the older style gunite spa jets is the length can be an issue. I have Starite equipment (heater and Filter) Location: Folsom, CA Spa Jets have weak whirlpool output Quote Postby jimmeep » Sat 18 Jan, 2014 16:14 I have a spa/pool combination controlled Video kiralandığında oy verilebilir. Like Bookmark April 2, 2011 at 10:54PM Thank you for reporting this comment.

Pool Spa Jets Weak

Overheat protection switch tripped: Allow unit to cool down and restart by pushing any key. I worked for a couple of afternoons trying to figure this out, taking out Ortega valve parts and such. The time now is 11:14 PM. Low water level: increase water level until the recommended level is reached.

Water Leaks Spa overfilled: Adjust spa water level. I don't know what valves would be involved, all I see are six heads coming out of the spa walls. IGP Anthony / Gunnite / 20 yr. Hot Tub Bubbles Not Working However, several locations make up the usual suspects.

NOTE: Assure that the GFCI is properly grounded and bonded. Helping people decide what is the right gear for meeting their needs. When we moved into this house in May, the spa blower motor did not work(old age). https://spapartsplus.com/update/docs/spu0114_Jets.html Yükleniyor...

The air line on the plugged jet is usually hooked to the air lines from other spa jets. Spa Air Venturi Not Working Jason Hughes 736.888 görüntüleme 7:55 Swimming Pool Service Tip: Unclogging Your Impeller - Süre: 2:38. I appreciate any suggestions! You should see 4 equal streams.

Spa Jets Not Working Properly

Too much water input – if the pump is oversized it can cause backpressure inside the jet after the orifice, this can cause the jet to not draw air correctly by Without the resistance, all the water was rushing out of the one jet. Pool Spa Jets Weak Scott Owner of - PoolGuyNJ LLC Expert Pool and Spa Repairs, Renovations, and Augmentation. Hot Tub Jets Not Blowing Air It's not uncommon for automated valves to need some adjustment from time to time.

Please Sign In to post comments #7 j lemus what is the correct Pool j lemus Posted Thu, 05/28/2015 - 15:56 what is the correct Pool plumbing pipe size/diagram for all, http://sparcweb.net/not-working/leisure-bay-spa-jets-not-working.php Once he replace the whirlpool motor, we notice five of the six jets were blowing very weakly, but the sixth was actually sucking. pool products ~ swimming pool pumps "Live in the sunshine, swim the sea, drink the wild air." ~ Ralph Waldo Emerson Reply With Quote 09-14-2016,08:46 PM #15 pcmacd View Profile Ozone bulb defective: Contact your local dealer. Swimming Pool Jets Not Working

I also forced air through the air line (through the standpipe) with a compressor to make sure it was also not plugged up same results. Besides that, I don't particularly want to heat the pool. Mark Hydraulics 101 ; Pump and Pool Spreadsheets ; Pump Ed 101 18'x36' 20k gallon plaster/gunite pool, 1/2 HP 2sp pump, Aqualogic PS8 SWCG, 420 sq-ft Cartridge Filter, Solar Panels, 6 Source Make sure the Equipment GFCI is set to ON.

Then contact the original company and explain that you are going to have the problem fixed. Some Spa Jets Not Working What would YOU do?Thanks for everyone's help.-JimPS: I've got great pictures of it all but not sure how to post them here. Pump or Blower power switch is OFF (if available): Set power switch to ON.

This is probably the answer to the thing, but I doubt it.

Like Bookmark April 2, 2011 at 10:53PM Thank you for reporting this comment. Home Pool School Forum FAQ Forum Actions Mark Forums Read Quick Links View Site Leaders PoolMath Rules What's New? I had a pool heater installed and when replumbing they went to a 1 pump system. Hot Tub Blower Works But No Bubbles I did this, and it cleared out the jets so that they could get air into them.

Sıradaki How to Clear Blockages in the Circulation Lines of a Pool : Pool Care - Süre: 1:51. The air gets mixed into the pressurized water by use of a venturi inside the jet. Mark Hydraulics 101; Pump Ed 101; Pump and Pool Spreadsheets; Pump Run Time Study; DIY Acid Dosing; DIY Cover Roller 18'x36' 20k plaster, 1/2 HP 2sp pump, Aqualogic PS8 SWCG, 420 have a peek here It's free!

I do not have a blower, just an air pipe. This is probably the first time I've tried to use it this year. Overheat protection switch tripped: Allow unit to cool down and restart by pushing any key. All pool filters incorporate a water-pressure gauge.

ehowathomechannel 114.150 görüntüleme 1:51 Why are there Air Bubbles in my Pool? I'm going to try blowing out the lines next. Water in air blower plumbing: Contact your local dealer. All rights reserved.

I'm just looking for some general operation and how these are normally plumbed. Leaving the pump under positive pressure, water passes through a multiport valve and into the filter. High Heat Temperature sensor not in drywell: Place sensor in drywell - or contact your local dealer. Rob Estell 57.228 görüntüleme 7:48 SWIMMING POOL PLUMBING SYSTEMS (800) 766 5259 www ePoolscapes com - Süre: 8:57.

I'm think the lack of bubbles and pressure is due to going down to one pump. I would think that if there was water in the piper it would have blown out when you lowered the water levels. This backpressure is between the orifice and the eyeball at the front of the jet where the water and air mixture come out. Running a screwdriver or other long, thin object through the orifice will often knock it loose, this works best with the jet pump running to help push the object out.

Social Media is a great equalizer and most companies understand that poor business practices no longer remain between the business and the client but it is important to remind them that Is it possible something is caught at a bend in a line or where a hose attaches to your standpipe? Of course the people who changed it for me claim that isnt so. Share this post Link to post Share on other sites lenayres 0 Newbie Members 0 1 post Posted July 4, 2009 · Report post Just wondering if you found an

Undo poolguynj They thread in. "Gently" tapping a flat head screw driver so it's edges bite the inside wall of the remaining piece should allow you to remove the remaining piece. The pool accessories run fine (ie. Polaris, water feature, jets, heater). Water leaking from spa side control: Contact your local dealer.

nt